Glass door refrigerators
Iscar Releases A Brand New Line Of Slitting Cutters Applying Tang-Grip Technology And The Strength Of Sumo Tec Grades Iscar at this time offers a family of high-performance slitting tools that join the convenience and security of Tang-Grip clamping with the increased durability of the revolutionary Sumo Tec insert grades. The idea, already verified successful in Tang-Grip parting tools, has now been spread to slitting cutters. In the patented Tang-Grip clamping system, inserts are press-fit into their pockets with a distinct hand tool, and are clutched tightly in place without the need without requiring clamps, upper jaws or set screws that can weaken the insert and block chip flow. The pocket composition uses cutting forces to hold the insert seated securely in position, preventing any prospect of insert pull-out. The Tang-Grip clamping system also fosters increased accurate slitting cuts plus longer pocket and insert lifespan. Iscar's Sumo Tec insert grades feature a unique post-coating treatment which considerably boosts tool life and reliability. Unveiled in late 2007, the completely new Sumo Tec treatment smooths the insert's coated surface to banish microscopic stress raisers, reduce heat and friction and increase chip flow. The result is improved toughness and opposition to chipping and built-up edge, all leading to longer tool lifespan. The golden-colored side on Sumo Tec inserts aides wear detection. Size for size, Tangslit cutters offer more teeth than Iscar's SGSF cutters, providing higher feed rates. Their higher rigidity leads to straighter, additional accurate cuts and lowered vibration even in large-diameter cutters. The brand new Tangslit TGSF cutters come in 100 to 160 mm diameters, 3 and 4 mm widths and can accommodate the exact same assortment of inserts as Tang-Grip parting tools. Several other sizes will be added. Existing Sumo Tec grades for Tangslit cutters include: IC808, with a tough submicron substrate beneath a Sumo Tec TiAlN PVD coating, giving remarkable resistance to impact loads and built-up edge. This grade is suggested for slitting heat resistant alloys, austenitic stainless steel, hard alloys and carbon steel. IC830, giving extra toughness for heavier parting & grooving including interrupted cuts. It is suited for all stainless steel & high temperature alloys. IC908, a hard, fine-grain substrate with remarkable chipping resistance, mixed with a brand new Sumo Tec TiAlN PVD coating. It is perfect for nodular or gray cast iron. IC928 and 928A, PVD TiAlN-coated tough grades suited for stainless steel, high temperature alloys and other alloy steels. These grades are additionally suggested for interrupted cuts and heavy operations. All Tangslit and Tang-Grip inserts are found in J- or C-type chipformer geometries from Iscar. Iscar Adds Their Latest Creations To A Extensive Line Of Effective Hole Making Solutions Iscar recently released several different drilling innovations to meet their customers needs. These new products are Sumocham Drill, DR-DH and Deep Drills. Drawing off of their experience Iscar has come up with new and innovative ways to increase productivity for the end user. The Most Recent In Carbide Endmill Configuration In A Long And Prosperous Family From Iscar Manufacturers and die & mold shops can eliminate chatter problems in many milling operations with Iscar's new Chatterfree endmills. The cutters' variable-pitch flute pattern eliminates harmonic vibration, the main source of chatter. This enables faster cutting and finer finish in rough or finish slotting, shoulder milling and cavity milling. Completely New Cutters And Carbide Insert Configurations From Iscar To Better Improve The Machining Method Iscar is introducing Penta 34 carbide inserts with a new PB chipformer. The PB chipformer features a single cavity with a positive rake, neutral shoulder angle, and a honed edge. It is actually a C-type chipformer with a different frontal edge. A Few Of Improvements In Carbide Inserts By Iscar Iscar is introducing a new unique milling system with tangential, clamped, butterfly-shaped LNKX carbide inserts. The butterfly-shaped insert has significant advantages compared to the current flat, square shapes. The new geometry has more cutting edges, positive rake face, reduced cutting forces resulting in higher performance. Completely New End Mills From Iscar Can Amplify Productivity While Lowering Costs Manufacturers and die & mold shops can banish chatter problems in numerous milling operations with Iscar's new Chatterfree end mills. The cutters' variable-pitch flute pattern eliminates harmonic vibration, the primary source of chatter. This enables faster cutting and finer finish in rough or finish slotting, shoulder milling and cavity milling. A Selection Of Advancements In Carbide Inserts From Iscar Through The Previous Decade Iscar is announcing a brand new unique milling system that includes tangential, clamped, butterfly-shaped LNKX carbide inserts. The butterfly-shaped insert has meaningful advantages compared to the current flat, square shapes. The new geometry has more cutting edges, positive rake face, decreased cutting forces resulting in better performance. Push Pull Testing For Building Industry With Calibrated Measuring Instruments. Stress Load Testing Procedures For On Site Proof To Testing Demands. Push Pull Testing for the Railway industry for proof of reliable anchor fixings. Calibrated push pull force gauges are used for stress load testing along with tensile strength pull testing procedures. Proof of load testing undertaken, measured, recorded in a reliable and standard way to BS5080 Part 1 standards. |
Disclaimer Privacy Policy Contact Site Map
Copyright 2010 @
www.glassdoorrefrigerators.net
